Ratliff Electric has served Greenwood and the surrounding Johnson County area since 1993, handling residential and commercial electrical work for homeowners, landlords, property managers, and businesses of every size. Whether you need a quick repair or a full-service installation, work is performed by licensed electricians who know the area and take the job seriously. Same-day electrical service is available for urgent situations, and a call to (463) 444-6595 gets you a quote with no guesswork.
Call today. Wired tomorrow. Powered for good.
Our electricians know the homes and wiring in this area, and the calls we get most often are the ones that catch people off guard. A dead outlet in the kitchen. Lights that flicker when the refrigerator kicks on. A breaker that trips every time you run the microwave. A switch that stopped working for no obvious reason. These are not minor inconveniences. Left alone, they can turn into real safety hazards.
When we arrive, we start with a thorough diagnostic. We trace the fault, explain what we find, and give you a clear picture of what the repair involves before we touch anything. If the fix calls for GFCI or AFCI protection to bring the circuit up to code, we handle that as part of the work. Ground-fault and arc-fault breakers are now required in most residential applications, and we make sure any repair we complete leaves the circuit safer than we found it.
Same-day electrical service is available when the situation cannot wait. Call and we'll get the current flowing right.
Outlet and switch work covers more ground than most people expect. We install and replace standard outlets, GFCI-protected outlets in kitchens and bathrooms, AFCI outlets, USB combination outlets, and outdoor weatherproof receptacles. If an outlet is cracked, loose, warm to the touch, or simply not working, we find out why and fix it correctly.
Switch work follows the same approach. We replace failed switches, upgrade to dimmer or timer switches, and add new switch locations where a room needs better control. Nothing about this work is complicated when it is done right the first time.
Lighting installation is one of our most requested services. We handle recessed lighting, LED retrofits, pendant lights, chandeliers, under-cabinet lighting, exterior and security lights, and landscape lighting circuits. If you are updating a kitchen, finishing a basement, or just replacing a dated fixture in the hallway, we wire it cleanly and make sure the circuit can carry the load.
Ceiling fan installation is straightforward when an existing box is already in place. When there is no existing wiring, we run a new circuit, install a rated fan box, and complete the wiring from scratch. We also handle fan replacements, remote-control conversions, and situations where a light kit needs to be added or removed. Reach out and an electrician will follow up.
Before a small wiring issue turns into a hazard, it usually shows up at the panel first. Breakers that trip repeatedly, fuses that blow, a panel that runs hot, or circuits that simply cannot keep up with modern demand are all signs that the electrical service may need attention.
We handle panel repairs, full panel replacements, and 200-amp service upgrades. If your home was built with a smaller service entrance and you are adding appliances, finishing a basement, or planning an addition, a panel upgrade is often the first step. We perform load calculations to size the new panel correctly, install subpanels where additional circuits are needed in a detached space, and update arc-fault and ground-fault breakers to current code in the process.
Transparent pricing with no hidden fees on any wiring job. You will know what the work costs before we start.
Older homes in the Greenwood area sometimes still carry knob-and-tube wiring or aluminum branch-circuit wiring from decades past. Both present real risks by today's standards. We handle full rewiring projects, knob-and-tube replacement, and aluminum-wiring remediation, including proper grounding and bonding throughout the home. If you are buying an older property or your inspector flagged the wiring, we can assess the situation and walk you through the options.
New wiring for additions, garages, basements, sheds, and detached structures is a regular part of what we do. We also run dedicated circuits for dryers, washers, refrigerators, dishwashers, and other major appliances that require a 240-volt or 50-amp circuit of their own. Sharing a circuit with a high-draw appliance is one of the most common causes of nuisance tripping, and a dedicated circuit solves it cleanly.
For commercial clients, we wire tenant improvements, office buildouts, and retail spaces. Whether you are fitting out a new suite or reconfiguring an existing space, we work to code and on schedule. Pick up the phone and we'll handle the wiring.
Johnson County's housing stock runs the range from older ranch homes built in the 1960s and 1970s to newer subdivisions that have grown up around Greenwood over the past two decades. Indiana's four-season climate brings both heavy electrical loads from heating and cooling equipment and a storm season that includes severe thunderstorms, tornadoes, and ice storms capable of knocking out power for days. The three services below come up constantly in this area, and for good reason.
Many homes in this part of Indiana were wired for a fraction of the electrical load a household carries today. Aging panels, undersized service entrances, and circuits that were never designed for modern appliances create problems that show up gradually and then all at once. We assess the existing panel, calculate what the home actually needs, and install a properly sized replacement. The process includes a clear quote before work begins and a final inspection to confirm everything meets current code.
Indiana's storm seasons are not theoretical. When a severe thunderstorm or ice storm takes down lines in Johnson County, outages can stretch from hours into days. We install the electrical side of standby and portable generator systems: the transfer switch, the panel connection, and all wiring needed to bring generator power safely into the home. We do not sell or service the generator units themselves, but we make sure the electrical hookup is done correctly so the system works when you need it.
A power strip with a built-in surge suppressor handles small fluctuations at a single outlet. It does not protect the wiring in your walls, your panel, or the appliances and electronics connected elsewhere in the house. Whole-home surge protection installs at the panel and catches large voltage spikes before they reach any circuit in the building. Given Indiana's lightning activity during storm season, this is a practical investment. We install surge protection devices as a standalone service or as part of a panel upgrade.
Level 2 home EV charger installation requires a dedicated 240-volt circuit, the right breaker size, and enough available capacity in the panel to support the load. We handle all of it. Before scheduling, it helps to know the make and model of your charger and whether your panel has room for a new 50-amp circuit. If it does not, we can discuss a panel upgrade at the same time.
We run the circuit, install the outlet or hardwire the charger, and make sure the load calculation accounts for everything else the panel is already carrying. If you are not sure what your home needs, a call to (463) 444-6595 is the right starting point.
Here is what most people get wrong about their wiring: they assume electrical work only comes up when something breaks. In reality, some of our busiest calls come from people in the middle of a renovation, a home addition, or a basement finish who realize partway through that the existing wiring cannot support the new layout. We work alongside contractors and homeowners on remodels, additions, garage conversions, basement builds, and new construction. We also wire detached garages, sheds, and outbuildings that need their own circuits.
Rental property owners and property managers call us regularly for outlet replacements, panel work, and circuit additions between tenants. We understand that turnaround time matters when a unit needs to be ready.
Electrical safety inspections are available for any situation where you need a clear picture of what you have. Pre-purchase inspections, pre-listing walkthroughs, and rental-property compliance checks all fall within what we do. If a home inspector flagged something, we can follow up with a detailed assessment and a straight answer about what the repair involves.
When you call for a quote, you reach a real local person who can talk through what you need and give you an honest picture of the cost. We do not pad estimates or add fees after the fact. Transparent pricing with no hidden fees on any wiring job is how we operate, and it has been that way since we opened.
Same-day electrical service is available for situations that cannot wait. We also schedule weekend work when the timing works for both sides. The process is simple: call, describe what you are dealing with, and we will tell you what the job involves and when we can be there.
Schedule it. We wire it. You're powered.
We are the local electrician for Greenwood and the communities surrounding it. Our service area covers Johnson County and reaches into neighboring areas, including Bargersville, Whiteland, New Whiteland, Franklin, Edinburgh, Trafalgar, Nineveh, Southport, and Beech Grove. If you are in the area and need electrical work done right, we are close by and ready to schedule.
A burning smell near an outlet, panel, or fixture, sparks when plugging something in, a breaker that will not reset after tripping, or any situation where you suspect live wiring is exposed or damaged should all be treated as emergencies. Do not try to investigate live wiring yourself. Call us right away and we will advise you on what to do while we get there.
If you suspect a serious fault, turn off the breaker for the affected circuit if you can do so safely, and unplug anything connected to that circuit. Do not use the outlet, switch, or fixture until we have assessed it. If the situation feels immediately dangerous, contact your utility company to shut off power at the meter and then call us.
A transfer switch isolates your home's circuits from the utility grid before connecting generator power. Without one, generator power can back-feed the grid and create a serious hazard for utility workers restoring power. We install transfer switches and interlock kits so your generator hookup is done correctly and legally, and so the system works safely when you need it most.
A whole-home surge protector installs at the panel and intercepts large voltage spikes before they reach any circuit in the building. This includes wiring in the walls, the panel itself, and every appliance and electronic device connected to the home. A power strip surge suppressor at a single outlet does not provide that level of protection for the rest of the house.
A Level 2 charger requires a dedicated 240-volt circuit with the correct breaker size and enough available capacity in your panel to support the load. We assess your panel, run the circuit, and either install the outlet or hardwire the charger depending on the unit. If your panel does not have room for a new 50-amp circuit, we can discuss a panel upgrade at the same time.
We start by looking at what you have: the panel, the existing wiring, and what you are trying to accomplish. For larger projects like a panel upgrade or a full rewire, we perform a load calculation and a visual inspection before recommending anything. We explain what we find and give you a clear quote before work begins so there are no surprises.
It depends on the job. Outlet and switch replacements often require turning off the breaker for that circuit, but the rest of the home stays live. Panel work, service upgrades, and rewiring projects require a more significant shutdown. We will tell you ahead of time what to expect so you can plan accordingly.
A full rewire is typically recommended when a home still has knob-and-tube wiring, when aluminum branch-circuit wiring is present and has not been properly remediated, or when the existing wiring is too deteriorated to safely support the home's current load. A partial rewire may address a specific area, such as a kitchen or a basement addition. We assess the condition of the wiring before recommending a scope.
We start with a call to understand what you are working with and what you need. From there, we schedule an on-site assessment, perform a load calculation, and give you a written quote. Panel upgrades typically require a permit and a utility coordination step for the service entrance, and we handle those logistics as part of the job.
Yes. When we finish a job, we walk you through what was done and why. You will receive documentation of the work completed, and the invoice will reflect exactly what was quoted. If permits were pulled, we handle the inspection coordination and make sure you have the paperwork you need.
We do not run outdoor wiring or install exterior fixtures during active rain or lightning. If weather delays a scheduled outdoor job, we will contact you to reschedule. For urgent outdoor repairs that cannot wait, we assess the situation and proceed when it is safe to do so. All outdoor wiring uses weatherproof materials and enclosures rated for exterior use.
During a panel inspection or service call that involves the panel, we look at the breaker condition, the wiring connections, the grounding and bonding, and whether AFCI or GFCI breakers are in place where current code requires them. We also check for signs of overheating, corrosion, or previous work that was not done correctly. If we find something that needs attention, we explain it before recommending any additional work.
We test every circuit, outlet, switch, or fixture we work on before we pack up. For outlet installations, that means checking for proper voltage and polarity. For panel work, we verify that each breaker is correctly labeled and that the circuits are functioning as expected. We do not consider a job done until the work has been tested and confirmed.
Ratliff Electric has been doing electrical work in Greenwood and across Johnson County since 1993. We handle residential and commercial projects of every size, same-day electrical service is available, and all work is performed by licensed electricians who take the job seriously. We've been part of this community long enough to know every road.
We stand behind every circuit we touch. Call (463) 444-6595 today to schedule your service or request a quote.
From a tripped breaker to a full panel upgrade, we handle the electrical work that keeps homes and businesses in Greenwood running safely. Whether you need a quick repair or a major installation, our licensed electricians show up on time, explain the work clearly, and get it done right. Below is a look at what we offer, who each service fits best, and a few things worth knowing before you call.
| Service | Scope of Work | Common Situations | What to Keep in Mind |
|---|---|---|---|
| Breaker & Fuse Repair |
| Any property where breakers are failing or a fuse box is still in service | A breaker that keeps tripping is telling you something. We find the cause rather than just resetting it. |
| Wiring for Additions & Remodels |
| Homeowners finishing a basement, adding a room, or remodeling a kitchen or bathroom | Remodel wiring is permitted and inspected. We coordinate with your general contractor or work directly with you. |
| Electrical Safety Inspections |
| Home buyers, sellers, and owners of older properties who want a clear picture of their electrical system | An inspection before closing can reveal wiring issues that affect both safety and the negotiation. We give you a straightforward report. |
| Lighting Installation |
| Homeowners upgrading lighting inside or out, or adding security lighting to the property | Outdoor and landscape lighting requires weatherproof wiring and proper circuit protection. We handle it to code. |
| EV Charger Installation |
| Homeowners with an electric vehicle who want faster, safer charging at home | A Level 2 charger requires a dedicated 240-volt circuit. We check your panel capacity first to make sure it can support the load. |
| Electrical Repairs & Troubleshooting |
| Homeowners or tenants noticing warning signs in their electrical system | Warm outlets, burning smells, or repeated tripping are not problems to wait on. Call the same day you notice them. |
| Wiring & Rewiring |
| Older homes in Johnson County with outdated wiring that no longer meets safety or code standards | Knob-and-tube and aluminum wiring are common in older homes here. Replacing them protects the home and can affect insurability. |
| Outlet & Switch Installation |
| Homeowners updating older outlets or adding convenience and code-compliant protection | GFCI protection is required by code in kitchens, bathrooms, garages, and outdoor areas. We install them to current standards. |
| Electrical Panel Upgrades |
| Older Greenwood homes adding EV chargers, appliances, or finished spaces that exceed current panel capacity | Panel upgrades require a permit and inspection. We handle the paperwork and coordinate with the utility so you don't have to. |
| Dedicated Appliance Circuits |
| Homeowners adding a major appliance or equipment that needs its own circuit | Running a high-draw appliance on a shared circuit is a common cause of tripping breakers. A dedicated circuit solves that. |
| Basement & Sump-Pump Circuits |
| Homeowners finishing a basement or protecting against water damage with a reliable sump-pump circuit | A sump pump on a shared circuit can lose power at the worst time. A dedicated circuit keeps it running when it matters most. |
| Whole-Home Surge Protection |
| Any home with sensitive electronics or appliances worth protecting from lightning and utility fluctuations | A single surge can damage multiple appliances at once. Panel-level protection intercepts the spike before it reaches your devices. |
| Ceiling Fan Installation |
| Any room that needs a ceiling fan, including rooms without an existing ceiling box | Installing a fan where there is no existing fixture requires running new wiring. We handle that as part of the job. |
| Backup Generator Installation |
| Greenwood and Johnson County homeowners who lose power during Indiana storm seasons | A properly wired transfer switch prevents back-feeding the grid, which protects both your home and utility workers. |
How do I know if my panel needs to be upgraded?
Common signs include breakers that trip frequently, a panel that feels warm to the touch, lights that dim when appliances run, or a panel that is still rated at 100 amps in a home that has added significant electrical load over the years. If you are adding an EV charger, finishing a basement, or running new appliances, we recommend calling us to run a load calculation before assuming your current panel can handle it.
What causes breakers to trip repeatedly?
A breaker trips when a circuit is drawing more current than it is rated for, or when a fault exists somewhere in the wiring. The most common causes are overloaded circuits, a failing breaker, a short circuit in a device or outlet, or a ground fault. Resetting the breaker without finding the cause is not a fix. We diagnose what is actually happening and correct it.
Is the electrical work permitted and inspected?
Yes. Panel upgrades, new circuits, rewiring, and most significant installations require a permit and a follow-up inspection by the local authority. We pull the permit, schedule the inspection, and make sure the work meets current code before the job is closed out. You should be cautious about any electrician who suggests skipping the permit process.
Same-Day and Emergency Availability
We keep time available for urgent calls because electrical problems do not always wait for a convenient moment. Call us and we will tell you how quickly we can get to you.
My home was built in the 1960s or 1970s. Is the wiring still safe?
Older homes in and around Greenwood often have knob-and-tube or aluminum wiring that was acceptable at the time but does not meet current safety standards. Whether it is safe depends on its condition and whether it has been modified over the years. We can inspect the wiring and give you an honest assessment of what, if anything, needs to be updated.
What does a whole-home surge protector actually do?
A whole-home surge protector installs at your main panel and intercepts voltage spikes before they travel through your wiring to your outlets and devices. Indiana sees regular thunderstorms and occasional utility fluctuations that can send a surge through the lines. A panel-level protector guards everything downstream, including appliances, electronics, and the panel itself. It is a straightforward installation that pays for itself quickly if a major surge ever hits.
What do I need for a Level 2 EV charger at home?
A Level 2 charger runs on a dedicated 240-volt circuit, typically a 50-amp circuit for most home chargers. Before we install the charger, we check your panel capacity to confirm it can support the added load without requiring an upgrade. If your panel is already near capacity, we will let you know what the options are before any work begins.
Upfront Quotes With No Surprise Fees
We give you the price before any work starts, and it does not change without a conversation first. What we quote is what you pay.
How does backup generator hookup work?
We install a transfer switch or interlock kit at your main panel that allows a portable or standby generator to power your home safely. The transfer switch isolates your home from the utility grid while the generator is running, which prevents back-feeding and protects both your equipment and utility workers. We size the hookup for your critical circuits and make sure everything is wired to code.
Do I need to be home when the electrician comes?
For most jobs, having someone present is helpful. We will walk you through what we find, explain the work before we start, and go over the results when we finish. If you cannot be there, call us ahead of time and we will figure out the best way to handle access and communication for your specific situation.
Experienced With Older and Newer Homes
Johnson County has a lot of older housing stock, and we know what to look for in homes that were wired decades ago. We bring the same care to new construction and remodels.
How does pricing work, and will the quote change once work starts?
We give you a clear price before any work begins. That price does not change without a conversation first. If something unexpected comes up once we are into the job, we tell you before we proceed. There are no fees added after the fact. You will know what you are paying going in.
When should I call an electrician instead of handling something myself?
Swapping a light bulb or resetting a tripped breaker is something most homeowners can do safely. Anything beyond that, including replacing outlets, adding circuits, working inside the panel, or tracing a fault, should be handled by a licensed electrician. Electrical work done incorrectly creates fire and shock hazards that are not always visible until they cause a serious problem. If you are unsure, call us and describe what you are seeing.
Is same-day electrical service available?
Same-day service is available for most calls, including urgent repairs. When you call, we will let you know what time slots are open and get you on the schedule as quickly as possible. If something feels unsafe, such as a burning smell, a sparking outlet, or a breaker that will not stay reset, call right away rather than waiting.
Every electrical job is different, and the best way to get an accurate answer for your situation is to call us directly at (463) 444-6595 so we can talk through what you need.
(463) 444-6595